HVAC Near You
Call
Furnace Repair · Near Me

Furnace Repair in Greenville

Get fast, fair pricing from licensed local pros. Typical Greenville cost: $70 – $225 installed.

Call now: (855) 321-3116
Licensed & insured Upfront pricing Same-day service
Flame sensor
$70 – $225
Igniter
$125 – $400
Blower motor
$350 – $1.3k
Control board
$275 – $700
0%sizing
Dialing inStep 1 of 3
Instant cost estimate

What's going on with your HVAC system?

  • Licensed
    & fully insured
  • Same-day
    service available
  • Upfront
    pricing, no pressure
  • Local
    pros, nationwide
Greenville pricing

Furnace repair cost by part.

Typical Greenville repair pricing including parts and labor. A diagnostic fee usually applies and is often credited toward the work.

Furnace repair costs in Greenville, Texas, typically range from $65–$175 for a diagnostic fee, plus parts and labor. With a median home age of 47 years, many systems need frequent repairs. Local installed pricing for common repairs includes flame sensor ($70–$225), igniter ($125–$400), blower motor ($350–$1,300), control board ($275–$700), and heat exchanger ($1,300–$3,100+). Texas requires a TDLR-licensed contractor to pull a mechanical permit for any furnace work, which adds to the cost but ensures code compliance. Given Greenville's hot-humid climate and mixed heating needs, a heat pump is often a strong fit for both heating and cooling, and the federal 25C tax credit (30%, up to $2,000 for heat pumps) can offset upgrade costs.

  • Diagnostic / service call
    Often credited toward the repair
    $65 – $175
  • Flame sensor or thermocouple
    Common no-heat cause on gas units
    $70 – $225
  • Hot-surface igniter
    Furnace clicks but won’t light
    $125 – $400
  • Blower motor
    No airflow / weak airflow
    $350 – $1,300
  • Heat exchanger
    Cracked exchanger often means replace
    $1,300 – $3,100+

* A cracked heat exchanger is a safety issue — on an older furnace, replacement is usually the call.

Pricing reviewed · Local data from U.S. Census ACS

HVAC systems in Greenville

U.S. Census ACS
Households
11,569
Homeowners
5,529
45% own
Median home value
$170,800
Median income
$60,510
Median home built
1979
Housing units
12,228

With a median home built in 1979, many Greenville AC and furnace systems are at or past their 12–15 year lifespan — a common reason replacements spike here.

Talk to a local pro

Ready to get your HVAC system serviced in Greenville?

Speak with a licensed, insured HVAC technician near you. Upfront pricing, same-day availability, no obligation.

  • Licensed & insured
  • Same-day availability
  • Upfront, no-pressure pricing
  • Local pros near you
Call now: (855) 321-3116

No obligation — talk through your options.

Licensed technician servicing an HVAC system
Local guide · Greenville

What’s different about Greenville.

Generic cost pages skip the things that actually decide your price and which system fits here — local code, climate, and the money you can claim back.

Recommended unit for Greenville

High-SEER2 heat pump

Given Texas’s hot-humid climate and mixed heating, high-seer2 heat pump is the sensible default for most Greenville homes. With a long, hard cooling season here, stepping up the SEER2 tier pays back through lower summer bills. A pro can confirm the right size and system for your home with a load calculation.

Sources: SEER2 Southeast region standards (Texas) · Texas heat pump rebates by utility 2026 · Texas HVAC permit requirements

What Greenville code requires

Installing or replacing an HVAC system in Greenville follows Texas rules under the state mechanical code. Here’s what applies statewide:

  • Permit

    Mechanical permit pulled by your licensed HVAC contractor; covers equipment, refrigerant, and the electrical disconnect.

    Required
  • SEER2 minimum

    Federal Southeast-region minimum for new split-system AC. Higher tiers cut bills and unlock rebates.

    14.3 SEER2 (Southeast, <45k BTU)
  • Load calculation

    Sizing by load calc — not rule of thumb — prevents an oversized unit that short-cycles and never dehumidifies.

    Recommended
  • Refrigerant
    R-454B / R-32 (R-410A phased down 2025+)
  • Good to know

    HVAC work must be done by a TDLR-licensed Air Conditioning & Refrigeration contractor, and the licensed contractor (not the homeowner) pulls the required mechanical permit.

    —

Sources: SEER2 Southeast region standards (Texas) · Texas heat pump rebates by utility 2026 · Texas HVAC permit requirements

Talk to a local pro

Not sure which rules and rebates apply to your home?

A licensed Greenville pro will walk you through code, the right unit, and what you can claim back — in one quick call.

Call now: (855) 321-3116

No obligation — talk through your options.

Money back in Greenville

Texas heating is mostly mixed, which shapes the money back:

The federal 25C tax credit (30%, up to $2,000 for a qualifying heat pump and up to $600 for a high-efficiency central AC) applies in every state, including Texas.

How it works

Comfort back in three steps.

  1. 1

    Tell us what’s wrong

    Use the cost tool or call — takes 30 seconds. No cool air, no heat, or time for a new system.

  2. 2

    Get matched with a local pro

    We connect you with a licensed, insured HVAC technician near you — often the same day.

  3. 3

    Repair or replace, fast

    Your pro confirms the price on-site and gets your comfort back. Most jobs done in a few hours.

Local insight · Greenville

Furnace Repair in Greenville, explained.

What moves the price

What Affects Furnace Repair Costs in Greenville

Repair prices vary based on the part needed, labor time, and permit requirements. Older homes (median built 1979) may have outdated systems that are harder to service. The required mechanical permit, pulled by the licensed contractor, adds a fee. Seasonal demand (high in winter) can also affect pricing. Choosing a heat pump instead of a furnace may qualify for federal tax credits, making upgrades more affordable.

Common Furnace Repairs in Greenville

1

Flame Sensor Failure

A dirty or faulty flame sensor prevents the furnace from igniting. Cleaning or replacement costs $70–$225.

2

Igniter Problems

A broken igniter stops the furnace from lighting. Replacement runs $125–$400.

3

Blower Motor Malfunction

A failing blower motor reduces airflow. Replacement costs $350–$1,300.

FAQ

Furnace Repair FAQs — Greenville

Yes, Texas requires a mechanical permit for furnace repair. Only a TDLR-licensed contractor can pull the permit; homeowners cannot.

Furnace Repair near Greenville

Get a furnace repair quote.

No heat? Compare licensed local pros fast.

(855) 321-3116 Available now · Same-day service
Call now: (855) 321-3116

Upfront pricing Same-day Licensed