Furnace Repair in Manvel
Get fast, fair pricing from licensed local pros. Typical Manvel cost: $75 – $225 installed.
- Flame sensor
- $75 – $225
- Igniter
- $150 – $425
- Blower motor
- $375 – $1.4k
- Control board
- $275 – $750
What's going on with your HVAC system?
- Licensed& fully insured
- Same-dayservice available
- Upfrontpricing, no pressure
- Localpros, nationwide
Furnace repair cost by part.
Typical Manvel repair pricing including parts and labor. A diagnostic fee usually applies and is often credited toward the work.
Furnace repair in Manvel, Texas, typically costs between $75 and $3,300+, depending on the component. Most homes were built around 2010, so systems are about 16 years old—an age where flame sensors, igniters, and blower motors often need attention. A diagnostic fee of $70–$175 is standard. Texas requires a TDLR-licensed contractor to pull a mechanical permit for any repair involving the gas or refrigerant circuit. Given Manvel's hot-humid climate, a heat pump is often recommended, but furnace repairs are still common for the heating side. The federal 25C tax credit (30% up to $600 for a high-efficiency central AC) may apply if a new system is installed, but not for repairs alone.
- Diagnostic / service callOften credited toward the repair$70 – $175
- Flame sensor or thermocoupleCommon no-heat cause on gas units$75 – $225
- Hot-surface igniterFurnace clicks but won’t light$150 – $425
- Blower motorNo airflow / weak airflow$375 – $1,400
- Heat exchangerCracked exchanger often means replace$1,400 – $3,300+
* A cracked heat exchanger is a safety issue — on an older furnace, replacement is usually the call.
Pricing reviewed · Local data from U.S. Census ACS
HVAC systems in Manvel
U.S. Census ACS- Households
- 4,506
- Homeowners
- 3,123
- 78% own
- Median home value
- $300,200
- Median income
- $105,188
- Median home built
- 2010
- Housing units
- 4,013
With a median home built in 2010, many Manvel AC and furnace systems are at or past their 12–15 year lifespan — a common reason replacements spike here.
Ready to get your HVAC system serviced in Manvel?
Speak with a licensed, insured HVAC technician near you. Upfront pricing, same-day availability, no obligation.
- Licensed & insured
- Same-day availability
- Upfront, no-pressure pricing
- Local pros near you
No obligation — talk through your options.
What’s different about Manvel.
Generic cost pages skip the things that actually decide your price and which system fits here — local code, climate, and the money you can claim back.
Recommended unit for Manvel
Given Texas’s hot-humid climate and mixed heating, high-seer2 heat pump is the sensible default for most Manvel homes. With a long, hard cooling season here, stepping up the SEER2 tier pays back through lower summer bills. A pro can confirm the right size and system for your home with a load calculation.
Sources: SEER2 Southeast region standards (Texas) · Texas heat pump rebates by utility 2026 · Texas HVAC permit requirements
What Manvel code requires
Installing or replacing an HVAC system in Manvel follows Texas rules under the state mechanical code. Here’s what applies statewide:
- PermitRequired
Mechanical permit pulled by your licensed HVAC contractor; covers equipment, refrigerant, and the electrical disconnect.
- SEER2 minimum14.3 SEER2 (Southeast, <45k BTU)
Federal Southeast-region minimum for new split-system AC. Higher tiers cut bills and unlock rebates.
- Load calculationRecommended
Sizing by load calc — not rule of thumb — prevents an oversized unit that short-cycles and never dehumidifies.
- RefrigerantR-454B / R-32 (R-410A phased down 2025+)
- Good to know—
HVAC work must be done by a TDLR-licensed Air Conditioning & Refrigeration contractor, and the licensed contractor (not the homeowner) pulls the required mechanical permit.
Sources: SEER2 Southeast region standards (Texas) · Texas heat pump rebates by utility 2026 · Texas HVAC permit requirements
Not sure which rules and rebates apply to your home?
A licensed Manvel pro will walk you through code, the right unit, and what you can claim back — in one quick call.
No obligation — talk through your options.
Money back in Manvel
Texas heating is mostly mixed, which shapes the money back:
- Stateup to ~$3,000 (ENERGY STAR heat pump, participating contractor)Austin Energy Home Energy Improvement / Power Saver heat pump rebate →
State or utility program — verify eligibility before you buy.
- Stateapprox $100-$275 per tonCPS Energy heat pump / high-efficiency AC rebate (SEER2 15.2+) →
State or utility program — verify eligibility before you buy.
- Stateup to ~$600 (ENERGY STAR equipment, licensed contractor)Oncor Take a Load Off Texas energy efficiency program →
State or utility program — verify eligibility before you buy.
- Federal30% of cost, up to $2,000Federal 25C tax credit — heat pump →
For a qualifying ENERGY STAR heat pump meeting the CEE efficiency tier. Claimed on your federal return.
The federal 25C tax credit (30%, up to $2,000 for a qualifying heat pump and up to $600 for a high-efficiency central AC) applies in every state, including Texas.
Comfort back in three steps.
- 1
Tell us what’s wrong
Use the cost tool or call — takes 30 seconds. No cool air, no heat, or time for a new system.
- 2
Get matched with a local pro
We connect you with a licensed, insured HVAC technician near you — often the same day.
- 3
Repair or replace, fast
Your pro confirms the price on-site and gets your comfort back. Most jobs done in a few hours.
Furnace Repair in Manvel, explained.
What affects furnace repair costs in Manvel?
Prices vary by the specific part (e.g., flame sensor $75–$225 vs. heat exchanger $1,400–$3,300+), labor rates, and whether a permit is needed. Manvel's median income of $105,188 supports standard market rates. Older homes (pre-2010) may have harder-to-access systems, raising labor time. The hot-humid climate means furnaces are used less than AC, so some contractors may charge a premium for off-season repairs. Always get an upfront diagnostic fee before work begins.
Common furnace issues in Manvel
Flame sensor failure
A dirty or faulty flame sensor prevents the burner from staying lit. Repair cost: $75–$225.
Igniter problems
A cracked or worn igniter stops the furnace from lighting. Replacement runs $150–$425.
Blower motor malfunction
A failing blower motor reduces airflow and heating efficiency. Cost: $375–$1,400.
Furnace Repair FAQs — Manvel
Yes, Texas requires a mechanical permit for any repair involving gas or refrigerant. Your TDLR-licensed contractor must pull the permit; homeowners cannot do it themselves.
Get a furnace repair quote.
No heat? Compare licensed local pros fast.