HVAC Near You
Call
Furnace Repair · Near Me

Furnace Repair in Murphy

Get fast, fair pricing from licensed local pros. Typical Murphy cost: $75 – $225 installed.

Call now: (855) 321-3116
Licensed & insured Upfront pricing Same-day service
Flame sensor
$75 – $225
Igniter
$150 – $425
Blower motor
$375 – $1.4k
Control board
$275 – $750
0%sizing
Dialing inStep 1 of 3
Instant cost estimate

What's going on with your HVAC system?

  • Licensed
    & fully insured
  • Same-day
    service available
  • Upfront
    pricing, no pressure
  • Local
    pros, nationwide
Murphy pricing

Furnace repair cost by part.

Typical Murphy repair pricing including parts and labor. A diagnostic fee usually applies and is often credited toward the work.

In Murphy, Texas, furnace repair costs typically range from $75 for a simple flame sensor replacement to over $3,300 for a heat exchanger. With a median home age of 21 years, many furnaces are due for maintenance or repairs. Murphy's hot-humid climate means furnaces are used primarily during mixed heating seasons, but cooling demand is high, making heat pumps a recommended system choice. All HVAC work must be performed by a TDLR-licensed contractor who pulls the required mechanical permit. The federal 25C tax credit offers up to $600 for qualifying high-efficiency AC or up to $2,000 for a heat pump, which can offset upgrade costs.

  • Diagnostic / service call
    Often credited toward the repair
    $70 – $175
  • Flame sensor or thermocouple
    Common no-heat cause on gas units
    $75 – $225
  • Hot-surface igniter
    Furnace clicks but won’t light
    $150 – $425
  • Blower motor
    No airflow / weak airflow
    $375 – $1,400
  • Heat exchanger
    Cracked exchanger often means replace
    $1,400 – $3,300+

* A cracked heat exchanger is a safety issue — on an older furnace, replacement is usually the call.

Pricing reviewed · Local data from U.S. Census ACS

HVAC systems in Murphy

U.S. Census ACS
Households
8,352
Homeowners
5,251
92% own
Median home value
$458,400
Median income
$152,847
Median home built
2005
Housing units
5,723

With a median home built in 2005, many Murphy AC and furnace systems are at or past their 12–15 year lifespan — a common reason replacements spike here.

Talk to a local pro

Ready to get your HVAC system serviced in Murphy?

Speak with a licensed, insured HVAC technician near you. Upfront pricing, same-day availability, no obligation.

  • Licensed & insured
  • Same-day availability
  • Upfront, no-pressure pricing
  • Local pros near you
Call now: (855) 321-3116

No obligation — talk through your options.

Licensed technician servicing an HVAC system
Local guide · Murphy

What’s different about Murphy.

Generic cost pages skip the things that actually decide your price and which system fits here — local code, climate, and the money you can claim back.

Recommended unit for Murphy

High-SEER2 heat pump

Given Texas’s hot-humid climate and mixed heating, high-seer2 heat pump is the sensible default for most Murphy homes. With a long, hard cooling season here, stepping up the SEER2 tier pays back through lower summer bills. A pro can confirm the right size and system for your home with a load calculation.

Sources: SEER2 Southeast region standards (Texas) · Texas heat pump rebates by utility 2026 · Texas HVAC permit requirements

What Murphy code requires

Installing or replacing an HVAC system in Murphy follows Texas rules under the state mechanical code. Here’s what applies statewide:

  • Permit

    Mechanical permit pulled by your licensed HVAC contractor; covers equipment, refrigerant, and the electrical disconnect.

    Required
  • SEER2 minimum

    Federal Southeast-region minimum for new split-system AC. Higher tiers cut bills and unlock rebates.

    14.3 SEER2 (Southeast, <45k BTU)
  • Load calculation

    Sizing by load calc — not rule of thumb — prevents an oversized unit that short-cycles and never dehumidifies.

    Recommended
  • Refrigerant
    R-454B / R-32 (R-410A phased down 2025+)
  • Good to know

    HVAC work must be done by a TDLR-licensed Air Conditioning & Refrigeration contractor, and the licensed contractor (not the homeowner) pulls the required mechanical permit.

    —

Sources: SEER2 Southeast region standards (Texas) · Texas heat pump rebates by utility 2026 · Texas HVAC permit requirements

Talk to a local pro

Not sure which rules and rebates apply to your home?

A licensed Murphy pro will walk you through code, the right unit, and what you can claim back — in one quick call.

Call now: (855) 321-3116

No obligation — talk through your options.

Money back in Murphy

Texas heating is mostly mixed, which shapes the money back:

The federal 25C tax credit (30%, up to $2,000 for a qualifying heat pump and up to $600 for a high-efficiency central AC) applies in every state, including Texas.

How it works

Comfort back in three steps.

  1. 1

    Tell us what’s wrong

    Use the cost tool or call — takes 30 seconds. No cool air, no heat, or time for a new system.

  2. 2

    Get matched with a local pro

    We connect you with a licensed, insured HVAC technician near you — often the same day.

  3. 3

    Repair or replace, fast

    Your pro confirms the price on-site and gets your comfort back. Most jobs done in a few hours.

Local insight · Murphy

Furnace Repair in Murphy, explained.

What moves the price

What Affects Furnace Repair Costs in Murphy

Repair costs vary based on the component needing replacement—flame sensors and igniters are more affordable, while blower motors and control boards cost more. Labor rates reflect the local market, and a diagnostic fee of $70–$175 is standard. The age of your furnace (median 21 years) may increase repair complexity. Permits required by the state add a small fee but ensure code compliance. Choosing a heat pump over a standard furnace may qualify for federal tax credits, reducing net cost.

Common Furnace Problems in Murphy

1

Flame Sensor Failure

A dirty or faulty flame sensor is a frequent issue, causing the furnace to cycle on and off. Repair costs $75–$225.

2

Igniter Malfunction

A broken igniter prevents the furnace from lighting. Replacement runs $150–$425.

3

Blower Motor Problems

A failing blower motor reduces airflow and efficiency. Repair or replacement costs $375–$1,400.

FAQ

Furnace Repair FAQs — Murphy

Yes, Texas requires a mechanical permit for furnace repair or replacement. Your TDLR-licensed contractor must pull the permit before starting work.

Furnace Repair near Murphy

Get a furnace repair quote.

No heat? Compare licensed local pros fast.

(855) 321-3116 Available now · Same-day service
Call now: (855) 321-3116

Upfront pricing Same-day Licensed