HVAC Near You
Call
Furnace Repair · Near Me

Furnace Repair in Selma

Get fast, fair pricing from licensed local pros. Typical Selma cost: $75 – $225 installed.

Call now: (855) 321-3116
Licensed & insured Upfront pricing Same-day service
Flame sensor
$75 – $225
Igniter
$150 – $425
Blower motor
$375 – $1.4k
Control board
$275 – $750
0%sizing
Dialing inStep 1 of 3
Instant cost estimate

What's going on with your HVAC system?

  • Licensed
    & fully insured
  • Same-day
    service available
  • Upfront
    pricing, no pressure
  • Local
    pros, nationwide
Selma pricing

Furnace repair cost by part.

Typical Selma repair pricing including parts and labor. A diagnostic fee usually applies and is often credited toward the work.

In Selma, Texas, furnace repair costs typically range from $70–$175 for a diagnostic fee, plus parts and labor. With a median home age of about 16 years, common repairs include flame sensors ($75–$225), igniters ($150–$425), and blower motors ($375–$1,400). Texas requires a TDLR-licensed contractor to pull a mechanical permit for any furnace work, which adds a small overhead but ensures code compliance. Given Selma's hot-humid climate and mixed heating needs, a heat pump is often recommended for efficiency, and the federal 25C tax credit (30%, up to $2,000 for qualifying heat pumps) can offset costs.

  • Diagnostic / service call
    Often credited toward the repair
    $70 – $175
  • Flame sensor or thermocouple
    Common no-heat cause on gas units
    $75 – $225
  • Hot-surface igniter
    Furnace clicks but won’t light
    $150 – $425
  • Blower motor
    No airflow / weak airflow
    $375 – $1,400
  • Heat exchanger
    Cracked exchanger often means replace
    $1,400 – $3,300+

* A cracked heat exchanger is a safety issue — on an older furnace, replacement is usually the call.

Pricing reviewed · Local data from U.S. Census ACS

HVAC systems in Selma

U.S. Census ACS
Households
4,427
Homeowners
2,192
55% own
Median home value
$262,000
Median income
$95,692
Median home built
2010
Housing units
4,023

With a median home built in 2010, many Selma AC and furnace systems are at or past their 12–15 year lifespan — a common reason replacements spike here.

Talk to a local pro

Ready to get your HVAC system serviced in Selma?

Speak with a licensed, insured HVAC technician near you. Upfront pricing, same-day availability, no obligation.

  • Licensed & insured
  • Same-day availability
  • Upfront, no-pressure pricing
  • Local pros near you
Call now: (855) 321-3116

No obligation — talk through your options.

Licensed technician servicing an HVAC system
Local guide · Selma

What’s different about Selma.

Generic cost pages skip the things that actually decide your price and which system fits here — local code, climate, and the money you can claim back.

Recommended unit for Selma

High-SEER2 heat pump

Given Texas’s hot-humid climate and mixed heating, high-seer2 heat pump is the sensible default for most Selma homes. With a long, hard cooling season here, stepping up the SEER2 tier pays back through lower summer bills. A pro can confirm the right size and system for your home with a load calculation.

Sources: SEER2 Southeast region standards (Texas) · Texas heat pump rebates by utility 2026 · Texas HVAC permit requirements

What Selma code requires

Installing or replacing an HVAC system in Selma follows Texas rules under the state mechanical code. Here’s what applies statewide:

  • Permit

    Mechanical permit pulled by your licensed HVAC contractor; covers equipment, refrigerant, and the electrical disconnect.

    Required
  • SEER2 minimum

    Federal Southeast-region minimum for new split-system AC. Higher tiers cut bills and unlock rebates.

    14.3 SEER2 (Southeast, <45k BTU)
  • Load calculation

    Sizing by load calc — not rule of thumb — prevents an oversized unit that short-cycles and never dehumidifies.

    Recommended
  • Refrigerant
    R-454B / R-32 (R-410A phased down 2025+)
  • Good to know

    HVAC work must be done by a TDLR-licensed Air Conditioning & Refrigeration contractor, and the licensed contractor (not the homeowner) pulls the required mechanical permit.

    —

Sources: SEER2 Southeast region standards (Texas) · Texas heat pump rebates by utility 2026 · Texas HVAC permit requirements

Talk to a local pro

Not sure which rules and rebates apply to your home?

A licensed Selma pro will walk you through code, the right unit, and what you can claim back — in one quick call.

Call now: (855) 321-3116

No obligation — talk through your options.

Money back in Selma

Texas heating is mostly mixed, which shapes the money back:

The federal 25C tax credit (30%, up to $2,000 for a qualifying heat pump and up to $600 for a high-efficiency central AC) applies in every state, including Texas.

How it works

Comfort back in three steps.

  1. 1

    Tell us what’s wrong

    Use the cost tool or call — takes 30 seconds. No cool air, no heat, or time for a new system.

  2. 2

    Get matched with a local pro

    We connect you with a licensed, insured HVAC technician near you — often the same day.

  3. 3

    Repair or replace, fast

    Your pro confirms the price on-site and gets your comfort back. Most jobs done in a few hours.

Local insight · Selma

Furnace Repair in Selma, explained.

What moves the price

What affects furnace repair costs in Selma?

Prices vary mainly by the part needed and labor time. For example, a simple flame sensor replacement is more affordable than a heat exchanger ($1,400–$3,300+). Older homes or those with limited access may increase labor. The required mechanical permit adds a small fee, and using a TDLR-licensed contractor ensures proper installation. Seasonal demand (winter) can also influence pricing.

Common furnace repair issues in Selma

1

Flame sensor failure

A dirty or faulty flame sensor prevents the furnace from staying lit. Typical repair cost: $75–$225.

2

Igniter problems

A broken igniter won't spark to light the gas. Replacement runs $150–$425.

3

Blower motor malfunction

The blower motor circulates warm air; failure leads to no heat. Costs $375–$1,400 to replace.

FAQ

Furnace Repair FAQs — Selma

Yes, Texas requires a mechanical permit for any furnace repair or replacement. Your TDLR-licensed contractor must pull the permit before starting work.

Furnace Repair near Selma

Get a furnace repair quote.

No heat? Compare licensed local pros fast.

(855) 321-3116 Available now · Same-day service
Call now: (855) 321-3116

Upfront pricing Same-day Licensed